Peak Design Clutch Camera Strap Review
A clutch is a product I normally associate with cars. A Peak Design car modification line up? That would definitely get my attention. In any case, I don’t foresee them heading in that direction anytime soon (much to my dismay).
As one would expect, when I am not driving, I am walking. When I am out roaming the streets with a camera in hand, I usually have my full-length camera strap wrapped and twisted around my wrist. I am not a big fan of having something hanging around my neck for too long. But I want the security of having my camera attached in some way.
I’ve had a few different wrist/hand straps in my time, but up until a year ago I had been using a Canon 5D Mk3 with a 24-70mm attached. It was quite weighty just having it on my wrist and no weight being supported anywhere else, so they were a rather short-lived carrying solution.
But now with the A7iii the weight is almost halved, so I figured I would give it another go. It’s been a mixed feeling using the Peak Design Clutch, but I have grown quite fond of it, so allow me to explain why below.
Peak Design Clutch Specs
- The small size
- It’s very light weight
- It is quite simple and not bulky at all
- Nice and tidy style and soft materials
- Not being able to use a tripod without removing the bottom mount
- The bottom mount requires the included hex key to remove
- Without another strap attached it is quite vulnerable to being dropped
- It can be tiresome on the hand and wrist depending on weight of the camera
Weight: 50g (123g as packed)
Max Length: 29 cm (11.4″)
Min Length: 20 cm (8″)
Width: 51 mm (2″)
The Peak Design Clutch comes packaged with 2 Anchors, an Anchor Mount which attaches to the bottom of the camera, a small triangle ring, a 4mm hex-key, and a handy little pouch to carry your remaining accessories.
It can attach to pretty much any camera, and if you don’t have a point large enough for the strap to loop through the small triangle ring may help.
The bottom Anchor Mount contains a 1/4-20 UNC thread (similar to tripods) to attach to most cameras, and allows you to hook up a total of 4 Peak Design Anchors.
Build & Appearance
Well, it’s definitely a looker, and it is definitely Peak Design. From the first look you can tell it belongs in their line-up. The Peak Design Clutch is aesthetically pleasing, yet very functional. One might say it is what one would want in a life-partner.
When I say it is definitely Peak Design, what I mean is that it follows a balance of both form and function. The materials used are durable, stylish, comfortable and are chosen to proficiently serve their purpose. This is definitely not a bad thing. They’re pretty heavy duty.
Peak Design advertise that the Clutch is “Made from premium materials and custom hardware inspired by high-end climbing gear” and that the “Clutch’s exterior shell is made from the same material that whitewater rafts are made of”.
Oh and the two other important facts include that it is “Strong enough to hold any pro camera/lens/accessory combo” and your hands won’t sweat from it either.
The padding is soft and not bulky, the strap is firm and tight, and the clip is stylish and strong. Just what you need when you’re carrying a camera that you must care about. But comfortable enough to use it for an extended period of time.
Ease of Use
I actually had some trouble threading the strap of the Peak Design Clutch through the little metal attachment on my camera, but once it was on there it was not going anywhere else!
The strap material that you loop through the attachment is rather solid and not particularly malleable at first. I’ve since attached and removed it a number of times for the sake of this review, and it’s definitely softened up since.
The Anchor Mount at the bottom, however, that was a rather seamless experience. You connect that just like you would a tripod plate and to tighten it you use the included 4mm hex-key (Allen Key/Allen Wrench).
Be sure to note that once you have the Anchor Mount installed, you won’t be able to attach your camera to a tripod without first removing it.
If you lose your included hex-key, you can use any other 4mm hex-key. It is not a propriety product or size. But don’t go rummaging through your old Ikea boxes, I already tried that, it turns out they tend to only ever include 3mm or 5mm sizes!
To adjust the length of the Peak Design Clutch, pull on the loose strap and slide it through the bracket, that’ll tighten up the size. It can be a touch difficult to readjust the length while using it, so best to fix that up beforehand. It’s that simple to set up!
So now you’ve got your Clutch set up, you’re ready to rock and roll. Here’s how you use it:
Step 1: Insert Hand.
Step 2: Don’t let go!
But wait! Now you’re out and about, and you’ve come to realise that you may be a little bit clumsy at times. You might be thinking, “if I trip over, I have a tendency to launch anything that I am carrying across the street. I like my camera, I don’t want to send it wildly flying through the air! What can I do?”
Well, let me tell you what you can do. You can go out and grab yourself a couple of extra Anchors and strap those little bad boys in to the bottom Anchor Mount!
If you use another pair of Peak Design Anchor Links you can attach any other strap you own to your camera along side your fancy new Peak Design Clutch.
Or, if like me, you also own a Peak Design Slide Lite you can hook that up. This way you have a choice, you can either use just the Peak Design Clutch, use the strap, or if you’re a wild child like me, you can use both!
If you’re not clumsy and you’re quite a sturdy person, you’re all set and ready to go. You’ll enjoy your Peak Design Clutch! And if anything is wrong with it, Peak Design offer a lifetime warranty on their products. Just hit them up and they’ll sort your right out.
Tommy’s Top Tip:Use the included keyring to attach the hex-key to your tripod somewhere. That way you’ll always have it on hand when you need to attach your camera to your tripod.
Value for Money + Discount Code
For the money, it’s pretty competitively priced. There’s a whole world of camera hand straps out there, available in a wide variety of different shapes and sizes. This one is balanced in both size and comfort.
It has Peak Design’s famous build quality, combined with a neat and unobtrusive size. What a great combination! The Peak Design Clutch definitely balances itself out in value.
Peak Design Clutch Review | Conclusion
I will admit, the Peak Design Clutch is not for everybody, nor is it great in every situation. Some may prefer the added security of having the camera attached to your body in some other way, other than just in your hand.
You may also want to relieve your hands of camera carrying duty and rely on your neck or shoulder instead. You may want to free your hands so they’re able to do other handy type stuff.
While I, at first, was not too fond of this as a carrying solution, I have now come to the conclusion that when paired with the Peak Design Slide Lite, it is a great solution.
Having the security of a full-length strap with the stability and comfort of the Peak Design Clutch, I feel this is a great pairing. This will probably become my everyday solution now.
Without the Slide Lite, I like having some other way to put the camera down and free my hands. Such as slipping it back in to my bag, or passing it to my wife to carry for me. It’s only fair after all the countless shopping bags I carry for her!
Disclaimer: All recommendations are impartial and based on user experience, with no bias to the products or the brand. The products in this post may contain affiliate links.